Long-Reach Hedge Trimmer Parts

Genuine STIHL Long-Reach Hedge Trimmer Parts

Shop genuine STIHL OEM long-reach hedge trimmer parts for maintenance and repair. Search by the OEM number first; otherwise verify the model, serial number, diagram, and component location before ordering.

If the original number cannot be read, confirm the STIHL model, serial information, parts diagram, and component location. Long-reach equipment can differ by shaft arrangement, head angle, blade version, power source, serial range, and configuration. Images do not confirm fitment. Check the listing for the stated application, quantity, and included hardware.

Shop Long-Reach Hedge Trimmer Parts by Assembly

Identify the section of the machine related to the repair before choosing a part. An uneven cut, damaged blade area, or irregular head movement may involve the cutter bar, blades, blade guard, gearbox, pivot, mounting hardware, or fasteners. A vibration, unusual sound, or loss of drive may direct inspection to the shaft, drive tube, coupling, gearhead, bearings, housings, clamps, or mounts. Starting, power, throttle, and control concerns should be checked through the applicable fuel, air, electrical, trigger, switch, cable, and connection assemblies.

• cutter bars, hedge trimmer blades, blade guards, blade hardware, covers, fasteners, and mounting components;
• gearheads, angle drives, pivot components, shafts, drive tubes, couplings, bearings, housings, clamps, and retainers;
• throttle triggers, lockouts, stop switches, grips, handles, wiring, cables, switches, covers, and control components;
• fuel tanks, fuel lines, filters, vents, intake items, carburetor components, air filters, seals, gaskets, and fittings;
• starter ropes, pulleys, recoil springs, ignition components, electrical connections, clips, and service hardware.

Blade, Cutter Bar, and Articulating Head Service

The cutting head is a connected assembly. Inspect the blades, cutter bar, guard, gearbox, pivot section, mounting pieces, and visible fasteners with the machine switched off and secured. Replace damaged, bent, excessively worn, loose, or missing components with the correct listed items. Do not operate a long-reach hedge trimmer with a damaged blade, cracked guard, loose head, missing fastener, abnormal vibration, or a cutting head that will not hold its intended position.

Blades, guards, hardware, and head components should not be selected from appearance alone. The exact model and configuration determine the correct replacement. Follow the operating instructions for the installed cutting head, wear suitable protection during service, and keep hands clear of the blades. If the repair affects the blade drive, pivot lock, gearbox, or another safety-critical area, seek qualified assistance when the procedure cannot be completed safely.

Shaft, Drive Tube, and Gearhead Components

Long-reach trimmers rely on correctly aligned shaft and drive parts to transfer power to the cutting head. Inspect the drive tube, shaft, coupling, gearhead, angle drive, bearings, housings, handles, clamps, mounts, cables, and fasteners as one operating path. A loose tube, worn coupling, cracked housing, missing clamp, damaged handle, worn bearing, or misrouted cable can affect cutting performance, reach, balance, and control.

Compare OEM references and application details before replacing a shaft, coupling, gearhead, control cable, or threaded component. Do not force a part into place if it does not seat normally. Check the relevant service procedure instead. Persistent vibration, suspected internal gear damage, a binding drive system, or shaft misalignment should be inspected by a qualified outdoor-power-equipment technician.

Fuel, Electrical, and Control-System Parts

A no-start condition, fuel leak, intermittent operation, poor throttle response, or switch issue can involve more than one system. Inspect the appropriate fuel tank, lines, filter, vent, intake, air filter, carburetor, starter, ignition components, cable, trigger, lockout, switch, wiring, connections, and covers before selecting a replacement. On battery-powered equipment, match electrical components only to the specified model and approved power-system configuration.

After service, make sure the trigger, lockout, stop switch, wiring or cable route, covers, guards, clamps, and mounting hardware are secure and function normally. Do not bypass a safety device or operate the machine with a damaged control, fuel leak, loose cover, missing guard, or unresolved problem.

Confirm Fitment Before Returning to Work

Use the original OEM part number as the first fitment check. If that reference is unavailable, compare the exact STIHL model, serial number, diagram, component position, listing description, and stated compatibility. Product images can show a related version, a complete assembly, or hardware sold separately. Confirm whether your repair also requires fasteners, clamps, seals, gaskets, blade hardware, covers, or mounting parts.

STIHL is a registered trademark of its respective owner. References to STIHL identify genuine branded parts and compatible equipment applications.